英语翻译the welding gun to be set by the pressure-reducing valve.Placing the check valve in parallel with the pressure-reducing valve allows free return flow when the weld cylinder retracts.Remote controlRegulating pump pressure from a remote sta

英语翻译the welding gun to be set by the pressure-reducing valve.Placing the check valve in parallel with the pressure-reducing valve allows free return flow when the weld cylinder retracts.Remote controlRegulating pump pressure from a remote sta
英语翻译
the welding gun to be set by the pressure-reducing valve.Placing the check valve in parallel with the pressure-reducing valve allows free return flow when the weld cylinder retracts.
Remote control
Regulating pump pressure from a remote station can be accomplished by using small,pilot relief valves connected to the systems main pilot-operated relief valve.With the 3-way solenoid valve de-energized,system pressure is limited to 1,500 psi in this circuit.Energizing the 3-way solenoid valve permits venting the relief valve to either 1,000 psi or 500 psi,depending on the position of the 4-way valve,which is determined by the pilot signal it receives.
Two pressures
Pilot-operated relief valves provide two pressures for the mold-close cylinder and the injection cylinder of this plastic molding machine circuit.With the manual valve in neutral,the air-operated valves are actuated to extend the mold-close cylinder at a maximum pressure of 2,000 psi.Operating the manual valve to extend the injection cylinder vents the 400-psi relief to tank and vents the 2,000-psi relief at 400 psi.High-pressure fluid is held by the check valve.
Pressure-control valves are found in virtually every hydraulic system,and they assist in a variety of functions,from keeping system pressures safely below a desired upper limit to maintaining a set pressure in part of a circuit.Types include relief,reducing,sequence,counterbalance,and unloading.All of these are normally closed valves,except for reducing valves,which are normally open.For most of these valves,a restriction is necessary to produce the required pressure control.One exception is the externally piloted unloading valve,which depends on an external signal for its actuation.
Relief valves

英语翻译the welding gun to be set by the pressure-reducing valve.Placing the check valve in parallel with the pressure-reducing valve allows free return flow when the weld cylinder retracts.Remote controlRegulating pump pressure from a remote sta
楼主,太小气了,才5分!
-------------------------
焊接枪是由减压安全阀.将止回阀与减压阀门允许自由回流焊接钢瓶时收回.
远程控制
从远程调节泵压站可以通过使用小、试点救济阀连接到系统的主要pilot-operated安全阀.与三通电磁阀不带电,系统压力限于1500磅.三通电磁阀允许充泄安全阀,要么1000 psi或500磅,取决于阀门的位置,而四大取决于它接收信号.飞行员
两方面的压力
提供两种压力减压阀Pilot-operated mold-close缸,为本塑料注射成型机圆柱电路.用手动阀门在中立、气动阀门驱动mold-close延长气缸压力最大的2,000磅.操作手动阀延长气缸通风口的400-psi注射救济的坦克和通风口2,000-psi救援在400磅.高压流体是由止回阀.
压力—控制阀门都发现几乎所有的液压系统,它们帮助各种功能,使系统压力低于预期安全维护一套上限部分电路的压力.救济、降低类型包括、顺序、平衡、卸载.所有这些都是正常关闭阀,除减少阀门,一般开.对于大多数的这些阀门、限制是必要的生产要求的压力控制.一个例外是外部驾驶,而这又取决于装卸瓶阀外部信号为其驱动.
减压阀

我只能通过“有道桌面词典”给你翻译（你可以下载一个）如下。有些地方还要你自己去理解（因为不一定是很正确的）
焊接枪是由减压安全阀。将止回阀与减压阀门允许自由回流焊接钢瓶时收回。
远程控制
从远程调节泵压站可以通过使用小、试点救济阀连接到系统的主要pilot-operated安全阀。与三通电磁阀不带电,系统压力限于1500磅。三通电磁阀允许充泄安全阀,要么1000 磅...

全部展开

我只能通过“有道桌面词典”给你翻译（你可以下载一个）如下。有些地方还要你自己去理解（因为不一定是很正确的）
焊接枪是由减压安全阀。将止回阀与减压阀门允许自由回流焊接钢瓶时收回。
远程控制
从远程调节泵压站可以通过使用小、试点救济阀连接到系统的主要pilot-operated安全阀。与三通电磁阀不带电,系统压力限于1500磅。三通电磁阀允许充泄安全阀,要么1000 磅或500磅,取决于阀门的位置,而四大取决于它接收信号。飞行员
两方面的压力
提供两种压力减压阀Pilot-operated mold-close缸,为本塑料注射成型机圆柱电路。用手动阀门在中立、气动阀门驱动mold-close延长气缸压力最大的2,000磅。操作手动阀延长气缸通风口的400-psi注射救济的坦克和通风口2,000-psi救援在400磅。高压流体是由止回阀。


压力—控制阀门都发现几乎所有的液压系统,它们帮助各种功能,使系统压力低于预期安全维护一套上限部分电路的压力。救济、降低类型包括、顺序、平衡、卸载。所有这些都是正常关闭阀,除减少阀门,一般开。对于大多数的这些阀门、限制是必要的生产要求的压力控制。一个例外是外部驾驶,而这又取决于装卸瓶阀外部信号为其驱动。
减压阀

收起